Sangharsh OS

Home/Download

Download Sangharsh OS

One ISO image. Write it to a USB stick, boot from it, and you are in a live KDE Plasma session in a couple of minutes.

Sangharsh OS — amd64

Live session and installer in one image · UEFI and Legacy boot

sangharsh-os.iso

Download ISO
KDE Plasma desktop amd64 UEFI + Legacy Live & installable 8 GB USB or larger

Live session login

Username Sangharsh
Password live

Use these to log in to the live session. They exist so you can try the desktop without touching your disk. The installer asks you to create your own username and password for the installed system.

Step two

Create the bootable USB

Pick the tool for the computer you are writing from, not the one you are installing to. All three do the same job: copy the ISO, sector for sector, onto the stick.

Everything on the USB stick will be erased. Check the drive letter or device name twice before you press the button. A 8 GB stick is enough; 16 GB gives you room to keep the ISO on the same stick.

Rufus

Windows

The usual choice on Windows. Small, portable, no installer.

  1. Download Rufus from rufus.ie and run it. No installation needed.
  2. Under Device, pick your USB stick. Check the drive letter against File Explorer first.
  3. Under Boot selection, press SELECT and choose sangharsh-os.iso.
  4. Leave Partition scheme on GPT with Target system UEFI for modern machines. Choose MBR only for an older BIOS-only computer.
  5. Leave the file system on FAT32 and press START.
  6. Confirm the warning about erasing the device, then wait for the green READY bar.

If Rufus asks whether to write in ISO Image mode or DD Image mode, take ISO Image mode first; fall back to DD mode if the stick will not boot.

balenaEtcher

Windows · macOS · Linux

The friendliest option, and the one that behaves the same on every system.

  1. Download balenaEtcher from etcher.balena.io and install or run it.
  2. Press Flash from file and select sangharsh-os.iso.
  3. Press Select target and pick the USB stick. Etcher hides system drives, which is why it is the safer choice for beginners.
  4. Press Flash! and enter your password if it asks for permission.
  5. Wait for Flash complete. Etcher verifies the write automatically.

On macOS, allow the app in System Settings → Privacy & Security if it refuses to open the first time.

dd

Linux · macOS

Already on the system, no download, no questions — and no confirmation either.

  1. Plug the stick in and find its device name:
    lsblk -o NAME,SIZE,MODEL,MOUNTPOINT
    A 16 GB stick usually shows up as /dev/sdb. Look at the size and model, not just the letter.
  2. Make sure none of its partitions are mounted:
    sudo umount /dev/sdb?*
  3. Write the image. Use the disk, sdb, not a partition, sdb1:
    sudo dd if=sangharsh-os.iso of=/dev/sdb bs=4M status=progress oflag=sync
  4. Wait for the prompt to come back, then flush the buffers:
    sync

Check the of= device twice. dd will happily overwrite your system disk without a single warning.

Verify the download

A truncated download produces a stick that boots to a black screen. Check the checksum before you write anything — it takes ten seconds.

# Linux / macOS
sha256sum sangharsh-os.iso

# Windows PowerShell
Get-FileHash .\sangharsh-os.iso -Algorithm SHA256

Compare the output with the SHA-256 published next to the ISO on the download page. If the two do not match exactly, download the image again.

Booting the stick

  1. Shut the machine down completely, plug the stick in, then power on.
  2. Tap the boot-menu key while it starts: usually F12, F11, F9 or Esc depending on the vendor.
  3. Choose the USB entry. On a UEFI machine it is often prefixed with UEFI:.
  4. Pick Live session at the Sangharsh OS boot menu and log in with Sangharsh / live.

If it will not boot

SymptomWhat to try
The stick never appears in the boot menuRe-write it in DD mode (Rufus) or with dd. Check the stick is formatted as GPT for UEFI machines.
Black screen after the boot menuAt the boot menu, edit the entry and add nomodeset to the kernel line — the usual fix for newer NVIDIA cards.
“Security violation” or a Secure Boot errorDisable Secure Boot in the firmware settings for the live session, or enrol the key if the installer offers it.
Installer cannot see the internal diskThe disk is probably set to RAID/Intel RST in the firmware. Switch it to AHCI.
Boots on one machine, not anotherLegacy BIOS machine with a GPT/UEFI stick. Re-write with MBR and Legacy target.

Try before you install. The live session is the full desktop running from RAM. Nothing is written to your disk until you start the installer, so you can check Wi-Fi, sound and suspend first.